$133.94 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 296293965679
eBay 1.Fit For 2001-2004 Ford Escape 2001-2004 Mazda Tribute 2.Package Includes: 2x Part# Front Sway Bars End Links – K80104 1x Part# Front Lower Control Arm And Ball Joint – Driver Side – K80398 2x Part# Front Outer Tie Rods Ends – ES3631 2x Part# Front Inner Tie Rods Ends – EV424 1x Part# Front Lower Control Arm and Ball Joint – Passenger Side – K80397 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. 8 Front Lower Control Arm Ball Joint Tie Rod For 01-04 Ford Escape Mazda Tribute 1.Fit For 2001-2004 Ford Escape 2001-2004 Mazda Tribute 2.Package Includes: 2x Part# Front Sway Bars End Links – K80104 1x Part# Front Lower Control Arm And Ball Joint – Driver Side – K80398 2x Part# Front Outer Tie Rods Ends – ES3631 2x Part# Front Inner Tie Rods Ends – EV424 1x Part# Front Lower Control Arm and Ball Joint – Passenger Side – K80397 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle Front Type Control Arm & Ball Joint Assembly Universal Fitment No Control Arm Construction Forged Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K80104 K80398 ES3631 EV424 K80397 OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends Superseded Part Number Front Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand ECCPP Manufacturer Part Number E80493102CP Adjustable Yes Greasable or Sealed Greasable Kit Included Surface Finish Premium Quality Kit Included 8 Pieces Cross Reference Part Number EC13224, YL8Z328EA 3L8Z378AB, 4L8Z378R Cross Part Number 5L843289AALR, 5L8Z3A13AA, 8L8Z3A13A, EC13228A, YL8C3289GA Partlink Number EC13415A, YL8Z5K483AA 3L8Z379AB, 4L8Z379L Fitment Stabilizer Bar Link Kit Control Arm and Ball Joint Assembly Bundle Description Sway Bar,Control Arm,Tie Rod End,Control Arm Features Greasable Finish Coated Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Item Specifics Placement on Vehicle Front Type Control Arm & Ball Joint Assembly Universal Fitment No Control Arm Construction Forged Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K80104 K80398 ES3631 EV424 K80397 OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends Superseded Part Number Front Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand ECCPP Manufacturer Part Number E80493102CP Adjustable Yes Greasable or Sealed Greasable Kit Included Surface Finish Premium Quality Kit Included 8 Pieces Cross Reference Part Number EC13224, YL8Z328EA 3L8Z378AB, 4L8Z378R Cross Part Number 5L843289AALR, 5L8Z3A13AA, 8L8Z3A13A, EC13228A, YL8C3289GA Partlink Number EC13415A, YL8Z5K483AA 3L8Z379AB, 4L8Z379L Fitment Stabilizer Bar Link Kit Control Arm and Ball Joint Assembly Bundle Description Sway Bar,Control Arm,Tie Rod End,Control Arm Features Greasable Finish Coated Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Discount Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means ECCPPAUTOPARTS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).ECCPPAUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (5).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (6).ECCPPAUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).ECCPPAUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales Universal 12V Low Pressure 5-9 PSI Electric Fuel Pump Installation Kit E8012S USD 14.15 ECCPP 2 Pcs Wheel Hub Bearing Front For Buick LaCrosse Century Regal Lesabre FWD USD 60.95 Pair For 2007-2014 Chevy Silverado Sierra Towing Power Heated LED Signal Mirrors USD 124.69 Pair Manual Adjust Tow Mirrors For 1988-1998 Chevy GMC C K 1500/2500/3500 USD 62.99 Front Wheel Hub Bearing For Chevy Monte Carlo Impala Cadillac Eldorado DTS FWD USD 40.38 Newly Listed ECCPP CV Joint Axle Fits Honda Foreman 450 2014-2019 Front Right Side USD 59.29 For 17-21 Alfa Romeo Giulia Carbon Fiber Highkick Trunk Spoiler USD 118.85 For 2011 2012 2013 BMW 335is Convertible Full Carbon Fiber Rear Spoiler USD 103.95 ECCPP CV Joint Axle Fits Yamaha Rhino 660 2006-2007 Rear Left Side USD 60.29 Fits 2015-2019 BMW F82 M4 Coupe Rear Trunk Spoiler Wing Glossy Carbon Fiber USD 121.29 8 Front Lower Control Arm Ball Joint Tie Rod For 01-04 Ford Escape Mazda Tribute 1.Fit For 2001-2004 Ford Escape 2001-2004 Mazda Tribute 2.Package Includes: 2x Part# Front Sway Bars End Links – K80104 1x Part# Front Lower Control Arm And Ball Joint – Driver Side – K80398 2x Part# Front Outer Tie Rods Ends – ES3631 2x Part# Front Inner Tie Rods Ends – EV424 1x Part# Front Lower Control Arm and Ball Joint – Passenger Side – K80397 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Items Included : Mounting Hardware Custom Bundle : Yes Interchange Part Number : K80104 K80398 ES3631 EV424 K80397 OE/OEM Part Number : Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : ECCPP Manufacturer Part Number : E80493102CP Adjustable : Yes Greasable or Sealed : Greasable Kit Included : Surface Finish : Premium Quality Kit Included : 8 Pieces Cross Reference Part Number : EC13224, YL8Z328EA 3L8Z378AB, 4L8Z378R Cross Part Number : 5L843289AALR, 5L8Z3A13AA, 8L8Z3A13A, EC13228A, YL8C3289GA Partlink Number : EC13415A, YL8Z5K483AA 3L8Z379AB, 4L8Z379L Fitment : Stabilizer Bar Link Kit Control Arm and Ball Joint Assembly Bundle Description : Sway Bar,Control Arm,Tie Rod End,Control Arm Features : Greasable Finish : Coated Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Item Specifics Placement on Vehicle Front Type Control Arm & Ball Joint Assembly Universal Fitment No Control Arm Construction Forged Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K80104 K80398 ES3631 EV424 K80397 OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends Superseded Part Number Front Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand ECCPP Manufacturer Part Number E80493102CP Adjustable Yes Greasable or Sealed Greasable Kit Included Surface Finish Premium Quality Kit Included 8 Pieces Cross Reference Part Number EC13224, YL8Z328EA 3L8Z378AB, 4L8Z378R Cross Part Number 5L843289AALR, 5L8Z3A13AA, 8L8Z3A13A, EC13228A, YL8C3289GA Partlink Number EC13415A, YL8Z5K483AA 3L8Z379AB, 4L8Z379L Fitment Stabilizer Bar Link Kit Control Arm and Ball Joint Assembly Bundle Description Sway Bar,Control Arm,Tie Rod End,Control Arm Features Greasable Finish Coated Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On DiscountShippingWarrantyReturnFeedback Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means ECCPPAUTOPARTS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).ECCPPAUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (5).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (6).ECCPPAUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).ECCPPAUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of ECCPP. All rights reserved.
Frequently Asked Questions About 8 Front Lower Control Arm Ball Joint Tie Rod For 01-04 Ford Escape Mazda Tribute in My Website
proorden.com is the best online shopping platform where you can buy 8 Front Lower Control Arm Ball Joint Tie Rod For 01-04 Ford Escape Mazda Tribute from renowned brand(s). proorden.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling 8 Front Lower Control Arm Ball Joint Tie Rod For 01-04 Ford Escape Mazda Tribute on proorden.com?
proorden.com helps you to shop online and delivers Valentino to your doorstep. The best-selling Valentino on proorden.com are: Valentino By Mario Valentino Fresia Sparkling Leather Sneaker Women’s Vintage V By Valentino For Women Eau De Toilette Spray 2.5oz New MISSING SPRAYER Valentino By Mario Valentino Handbag US 6 / EU 36 – Valentino Garavani Tan-Go Patent Leather Pump 70mm – Light Ivory valentino handbag black VALENTINO Rockstud Shoulder Bag S Leather Pink Red Valentino Gold Leather Stilettos Sandals(Size 7,37) Vendetta By Valentino For Women Mini EDT Splash 0.25oz New Sealed Vintage VALENTINO GARAVANI Rockstud Pumps Ivory Size 38 Made In ITALY Auth Valentino Garavani Womens Leather Pointed Toe Lace Up Stilettos Black Size 7 Valentino Upvillage Leather Sneaker Women’s VALENTINO CLASSIC BY VLENTINO 2.5 OZ/75 ML EDT SPRAY FOR WOMEN NEW NO BOX Valentino Beige Zipper pouch + Mini Born In Roma EDP 6ml + Mini Born In Roma EDT Valentino Donna Born in Roma Intense Eau de Parfum Spray 3.4 oz, New In Box Valentino Garavani Backnet Perforated Leather Sneakers Size 37.5 Eb0924loxsa Valentino rockstud Flat flip flop sandals Size 37 Made In Italy US 6.5/7 Valentino Logo Midnight Black Virgin Wool Scarf 16” x 63” Plus 3” Fringe Italy Valentino SHW Tote Bag Calfskin Leather/Canvas Multicolor Valentino Garavani Red Leather Side Bow Slingback Sandal Open Toe Size IT 35 US5 Valentino Garavani Peep Toe Patent Yellow Leather Heels 5” Sz 9.5 Valentino Bow Ribbon Pump Heels Patent Leather Black Size 7 US, 37 IT Valentino red embellished party dress size 4 Valentino Shoes 39.5 Calf Skin Pumps Valentino Skirt Sz 8 Vintage Velvet Quilted Straight Pencil Green Color Lined Valentino Garavani Rockstud Fringe Mules Heels Shoes Sandals £580 EU 39 UK 5 Auth VALENTINOGARAVANI Rockstud – Pink Pink Beige Patent Leather Leather Sandals VALENTINO Boutique Womens ITALIAN WOOL Jacket Blazer Size 4 Pink SOFT Button Authentic Valentino VALENTINO Cut dress #270-003-910-9177 Valentino Red Valentino Pink Knit Shift Dress S Valentino Garavani Womens PM Thong Pink Thong Sandals 40 Medium(B,M) BHFO 2682 Valentino By Mario Valentino Clara Monogram Leather Pump Women’s $545 VALENTINO GARAVANI Nude Velvet Ballerina Rockstud Velvet Flats 6.5 – 7/ 37 Valentino Vlogo 60 Leather Sandal Women’s Valentino Garavani Riding Boots Flat Knee High Tall Fringe Black 35/4.5-5 $1845 RED BY VALENTINO TWEED FLATS WITH BOW SZ 37.5 = 6.5 VALENTINO Belted Fit and Flare Mini Dress size IT 46 Black Valentino Garavani White Leather Beaded Lucite Sandal Block Heels 39/8.5 Valentino Women’s Tabitha Gold Slide Sandal Size 10 Valentino Red Valentino Taffeta Bow Detail Jacket in Black Silk Valentino Ruffle V-neck Dress Size 6 Sleeveless Shift Cocktail Night Out Peplum Pre-Owned Valentino Ivory Leather wedge with Rock Stud Accents Valentino Garavani size 36 sandal heels brown t strap faux tortoise/silver 1 1/2 Amazing NWT RED VALENTINO Black Bubble Hem/Bow Decorated Sleeveless Dress Sz 44 Valentino Metallic Light Purple Nuage Bow Tote Handbag VALENTINO GARAVANI Sandals BlackxCharcoal grayxSilver etc. 2200372199205 Red Valentino Size 44 / US 6 Black Silk Sleeveless Ruffled Cocktail Dress Used Valentino Garavani Pumps Heel Suede Brown EU36 US6 Japan F/S VALENTINO Rockstud Clutch Bag #Rc4219 VALENTINO GARAVANI Black Lace Up Leather Trimmed Velver Sandals Size 36.5 Boho RED VALENTINO Coat (Other) Navy 42(Approx. M) 2200406367075 Valentino Boutique MI Italy Luxury dove gray and off white silk blouse 6-8 VALENTINO Monogram Beige Leather Pumps Heels Shoes ITALY 9M $1690 Valentino Women’s Pink Silk Long Sleeve Self-Tie V-Neck Blouse Top Size 40 Valentino Garavani Patent Leather Shoulder Bag Purse or Clutch Black Ruffles Valentino Flower Cut-Out Dress – White – Size 6 Valentino rockstud cut out t-strap black VALENTINO VNTG BROWN SATIN 4” HEELS GOLD TONE & RHINESTONE FLOWER OPEN TOE 38.5 Vintage Valentino Navy Blue Wool Skirt Size 10 Valentino Rockstud 60 Leather Sandal Women’s Pink 40 4 Vials Valentino Voce Viva Eau de Parfum Spray 1.2 ml/0.04 fl oz Ea. Free Ship/ Valentina Assoluto by Valentino 1.7 oz 50ml EDP Intense Sealed Box Valentino Garavani 5mm Roman Stud Slide Nappa Size 9.5 US SET OF ROCK’N ROSE VALENTINO THE COLLECTION 3 VIALS 2 ML Each In Travel Box Valentino Black Short Sleeve Lace Inset A-Line Dress Size XS Valentino Rockstud Nylon Double Strap Espadrille Sandals Black Size 38 NEW Valentino Donna Born In Roma 0.5oz/15ml Eau De Parfum for Women Free Ship VALENTINO GARAVANI Lace Ribbon Pumps High Heel Open Toe size 37 Black Stiletto Valentino Dress Large Wool Silk Knit Knee Length Tank Pleated Cream Beige Valentino Leather Silver Rock Stud Slides EU36 US6 Valentino Donna Born In Roma INTENSE Eau de Parfum MINI Splash 6ml/0.2oz NIB Valentino Uomo Born In Roma Green Stravaganza For Men 3.4 oz/100ml EDT Valentino By Mario Bugola Logo Black Leather Slip On Flat Slides 37 Red Valentino Shift Dress, Tag, Size 40, Purple Black Amoeba, Women’s Designer Valentino Elegant Black Womens V-Neck Ruched Dress 4 Italy Fine Rosette Accent Valentino Classic by Valentino 75 ml/ 2.5 oz Eau de Parfum Spray (T) Valentino Garavani Rockstud Black Platform Pumps Heels Size 36.5 FLAWS Valentino Garavani Roman Stud Wool Shearling Slide Sandals US 6/Eur 36 New sz 9 / 39 Valentino Garavani Gold Sequined Slingback In-Heel Pump Shoes VALENTINO GARAVANI Rockstud Leather Tote 2way Bag Red made in ItalyⓁ Valentino Garavani VLogo Signature Rubber Thong Sandals – Size 37 (7) NDS Valentino Garavani Brown Designer Luxury Hand Shoulder Bag (EXCELLENT) VALENTINO Calfskin Rock Studs Heel Sandals Mules Shoes Women EU 37 Beige New Red Valentino Flower Puzzle Stud Leather Slide Sandals 10U.S./40Eu MSRP$529 Valentino by Mario Valentino Afrodite Quilted Leather Sandals Orange Size 7! Valentino Donna Born in Roma Green Stravaganza 3.4 oz EDP $425 Valentino Garavani Women Gold Studded Jelly Flat Thong Sandal EU 40/US 10 Valentino Donna Born In Roma Intense 3.4 oz EDP Spray For Women NEW IN BOX VALENTINO Black Wool Pencil Straight Midi Skirt Size 36 New Valentino Orlandi Red & Gold Hardware Chain Crossbody Bag – Faux Leather Valentino Garavani Upflair Feather Ankle Wrap Heels 6.5 US 36.5 EU VALENTINO GARAVANI Braided Shoulder Bag Leather Black Used VALENTINO GARAVANI “BOW” Black Satin open toe pumps Size 39.5 New RED Valentino Black Mini Sleeveless Dress Size IT 40 Small Metallic Grommet 3 Pcs Valentino Donna & Uomo Born in Roma EDP Set 6ml/ 0.2 fl oz with Pouch, NIB Valentino Donna Born in Roma Yellow Dream – Splash 0.2 oz – NWOB VALENTINO Beaded Shirt Peace T-Shirt One Size $1,400 Retail Natale Tee Auth VALENTINOGARAVANI Rockstuds 23 shoulder bag – Black Leather Shoulder Bag VALENTINO GARAVANI women’s shoes (RED) 36 ½ EU – NEW IN BOX – Authentic – Italy VALENTINO GARAVANI -NEW- Black Velvet Lace-Up Leather Flat Sandal 7 Mens Pullover Fleece Hoodie